Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Spring Replacement Cost in Studio City?
Spring repair in Studio City typically runs $180 – $340, and most jobs are finished in a single visit. That range covers replacing a broken torsion or extension spring on a standard residential door. Doors with two springs, heavier custom doors, or springs paired with worn cables usually land at the top of the range or slightly above it.
We’re Mustang Garage Door Service, and torsion and extension springs are one of the things we handle most often across the Valley. If your door slammed down or won’t lift off the ground, the spring is almost always the reason. Call (855) 633-3903 for a free estimate and we’ll give you a real number for your door, not a phone-book guess.
Key Takeaways
- Standard spring replacement in Studio City: $180 – $340, with most single-spring jobs near the middle.
- Two-spring doors and heavy custom doors cost more because there’s more hardware and more labor.
- Springs rarely fail alone; worn cables and rollers add cost, so we quote the whole picture.
- Never try to wind or unwind a torsion spring yourself. That’s the one part of a garage door that can seriously hurt you.
- Free estimates, upfront pricing, and brand-agnostic diagnosis on LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor systems.
Spring Replacement Cost Breakdown (2026)
Here’s how the numbers break down for a typical Studio City home. The ranges below are what we see in this market as of 2026.
| Job | Typical Price Range | Notes |
|---|---|---|
| Torsion spring replacement (single) | $180 – $260 | Standard 7-8 ft door, one spring |
| Torsion spring replacement (pair) | $260 – $340 | Two-spring setups, common on wider doors |
| Extension spring replacement | $180 – $280 | Older doors using side-mounted springs |
| Spring + cable repair | $280 – $440 | Cables usually wear alongside springs |
| Full spring and hardware refresh | $400 – $600 | Springs, cables, rollers, bearings |
| Related: cable repair | $130 – $250 | Often paired with spring work |
| Related: roller replacement | $110 – $220 | Worth bundling if rollers are shot |
| Related: garage door repair (general) | $150 – $600 | Broad range for non-spring fixes |
What pushes a job to the top of the range? Heavier doors, high-lift or custom tracks, and springs that failed along with the cables. What keeps it low? A straightforward single-spring swap on a standard door with nothing else worn out. We quote the whole repair up front so you’re not surprised halfway through.
If you want the full picture of how we handle the job itself, our Spring Replacement in Studio City page walks through the process from diagnosis to the final balance test.
What Affects Spring Replacement Pricing in Studio City
Every door is a little different, and a few things move the price more than others. Here’s what we weigh when we quote a spring job here.
- Number of springs. Single-spring doors cost less. Two-spring setups are common on wider and heavier doors, and they take more hardware and more time.
- Door weight and material. A steel door on a standard frame is the easy case. A solid wood or insulated custom door weighs significantly more, which means heavier-gauge springs and more labor.
- Condition of cables and rollers. When a spring snaps, it often takes a cable with it. Replacing both at once costs less than two separate visits, and it’s safer than leaving a frayed cable in place.
- Spring type. Torsion springs (mounted on the shaft above the door) and extension springs (mounted on the sides) use different setups. Older Studio City homes still running extension springs sometimes need a conversion to torsion, which changes the scope.
- Access and door height. A standard 7-foot door is the baseline. Taller doors and tight garages take longer and use different springs and hardware.
- Whether you catch it early. A door that’s starting to feel heavy or sounds wrong is a much cheaper fix than a door that failed hard and bent a track or a panel on the way down.
How to Save on Spring Replacement
Springs are a wear item. They’re rated for a set number of cycles, so they fail eventually no matter what you do. That said, a few habits keep the bill at the low end of the range.
- Listen for the early warning. If the door feels heavier than usual, lifts unevenly, or makes a sharp bang when it opens, get it looked at before it fails completely. Catching it early keeps the job to a spring swap instead of a spring plus a bent track.
- Don’t run the opener on a door that’s already struggling. The motor fights the failing spring and can burn out, which turns a $180 spring job into a spring repair plus an opener repair.
- Bundle related wear items. If your cables or rollers are also worn, replacing them in the same visit costs far less than two separate calls. Our garage door repair team does the whole job in one stop.
- Get a real quote, not a phone estimate. A spring price depends on the door in front of us. A free estimate lets us give you a firm number before any work starts. Call (855) 633-3903 to set one up.
- Skip the cheapest spring. Springs are rated by cycle life. A slightly better spring costs a little more up front and lasts noticeably longer, which is the real savings over a decade.
Every estimate we give is free and upfront. No surprise charges, no upsell. We look at the door, tell you what it needs, and let you decide.
Why Springs Fail Here in Studio City
A spring’s lifespan is measured in open-and-close cycles, not years. Most standard springs are rated somewhere around 10,000 cycles. A household that opens the door four times a day will get years out of one, while a busy household will wear it out faster. Heat and dry air also dry out springs and the grease that keeps them moving smoothly, so we see plenty of spring failures in the summer and early fall across Studio City.
Older homes near the hillsides and down in the flats around the Burbank and Sherman Oaks borders often have original springs that are well past their rated cycles. When a door that ran fine for years suddenly won’t open, a tired spring is usually the reason. That’s not an age problem. It’s just wear.
What We Work On
Mustang Garage Door Service is the multi-brand specialist, and that matters for spring work. We show up already fluent in whatever system is on your door – LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, or Raynor. The right spring, the right gauge, the right tension for your door. Brand-agnostic means we recommend what your door actually needs, not what’s convenient to sell.
We handle three things and do them well: garage door repair, garage door opener repair, and garage door installation. From a single broken spring to a full new door, you don’t need a second company. If the door’s worth saving, we repair first. If it’s genuinely at the end of its life, we’ll tell you that honestly too.
A Note on Safety
Torsion springs are stored energy. A wound spring is under hundreds of pounds of tension, and a spring that lets go during handling can cause serious injury. The winding bars and technique involved are tools of the trade, not a weekend project. This is the one part of garage door work where we actively steer people away from DIY.
What you can safely do is check for warning signs: look for a visible gap in a torsion spring above the door, listen for a bang, and test whether the door feels heavy when you lift it by hand with the opener disconnected. If something’s off, call a trained technician. It’s not worth the risk.
FAQs – Spring Replacement Cost
How much does spring replacement cost in Studio City?
Spring replacement in Studio City costs $180 – $340 for most homes. That covers a standard single-spring swap up to a two-spring setup on a wider or heavier door. Doors with worn cables or rollers sometimes run higher. Call (855) 633-3903 for a free estimate and a firm number for your door.
Is it cheaper to replace one spring or both?
Replace both if your door has two springs and they’re the same age. Springs wear at the same rate, so once one fails the other usually isn’t far behind. Doing both at once costs a bit more than a single spring but far less than two separate service calls. Call (855) 633-3903 to talk through what your door has.
Can you replace a spring the same day?
Yes – spring replacement is one of the fastest repairs we do. In most Studio City homes, a standard spring swap is finished in a single visit, often in under two hours. Availability varies, so call (855) 633-3903 and we’ll tell you the soonest we can get out.
My door won’t open – is it the spring or the opener?
A door that won’t open at all is usually a spring or cable failure, not the opener. If the motor runs but the door doesn’t move, look for a visible gap in the spring above the door. A clicking opener with a still door is a different problem, usually the opener itself. Call (855) 633-3903 and we’ll diagnose it before quoting anything.
Do you repair or replace a door with a broken spring?
We repair first. A spring failure is almost always fixable, and the rest of the door is usually in fine shape. Full door replacement runs $700 – $2,200, so it only makes sense when the door itself is warped, rusted through, or genuinely past its life. Call (855) 633-3903 for an honest read on your door.
Get a Free Spring Replacement Estimate in Studio City
A broken spring is a quick fix when it’s handled by someone who knows your door. We work on all eight major brands and tell you straight what the job needs – no upsell, no brand push. Free estimates, upfront pricing, and a repair-first approach that keeps money in your pocket when the door’s worth saving.
Call Mustang Garage Door Service at (855) 633-3903 for a free estimate on spring replacement in Studio City. We’ll give you a real number, show up with the right parts, and get your door moving again.
Pricing reflects the Studio City market as of 2026. Mustang Garage Door Service offers free estimates – call (855) 633-3903.
What Our Customers Say
"Keypad stopped working, which I assumed meant a whole new system. It was the batteries and a reprogram. He charged me the minimum service call and told me how to do it myself next time."
- Leela Patel"The old chain drive sounded like a freight train through the bedroom above the garage. Went with the belt drive they recommended and now I genuinely cannot hear it open from upstairs."
- Doug Schaefer"Opener works, remotes are programmed, no complaints on the work. Took three days to get on the schedule though, so if you've got a car trapped inside, say so when you call."
- Ryan Brooks